Unbalanced vs. Balanced Lines
How they work and the difference between them. By Al Keltz
Unbalanced signal lines are characterized by the fact that the cable and connectors use only two conductors, a center conductor surrounded by a shield. Examples of unbalanced wiring are found in tip/sleeve 1/4” guitar cords or the cables used with many CD players and tape decks which terminate with RCA phono type connectors.
In an unbalanced configuration, the shield surrounds a single center conductor. The shield stays at a constant ground potential (as it is connected to ground when plugged into equipment) while the signal voltage in the center conductor varies in a positive and negative manner relative to it. Because the shield completely surrounds the center or “hot” conductor and is connected to ground, it intercepts most of the electrical interference encountered by the cable and passes it away harmlessly to ground. Very little or no interference will be able to reach the center conductor where it would interact with desired signal. Because the shield is one of the two conductors required to complete the circuit, it must always be connected at both ends of the cable. This may set up a condition called a “ground loop” that sometimes produces hum when the grounds of different pieces of electrical equipment are connected to each other. (Note: A shield that consists of wire that is braided instead of just spun around the center in a spiral will provide superior coverage. Spiral shield is less expensive but can spread apart when the cable is flexed, exposing the center conductor to unwanted hum and buzz.)
If outside electrical interference does manage to penetrate the shield, it will mix with the desired signal that is present in the center conductor and be amplified right along with it as noise, buzz, etc. This might not be a huge problem with electric guitars, tape decks and unbalanced microphones when the cable is only a few feet long. But in environments containing a lot of interference or when an unbalanced signal is sent long distances, such as down a snake, it will become more and more susceptible to unwanted interference. This problem can be alleviated with the use of balanced lines.
Whirlwind Accusonic+1 unbalanced cable features braided pure copper shield with carbon extrusion between the braid and center conductor to provide extra shielding and reduce microphonics and handling noise.
Balanced lines are characterized by the fact that there are two center conductors for the signal, usually surrounded by a shield and these conductors have an equal impedance to ground. This shield is connected to ground like unbalanced lines but it is not required as one of the signal conductors. In fact, some balanced cables like CAT-5 twisted pair data cables and analog telephone lines don't have a shield at all.
The sole purpose of the shield is to provide extra defense against unwanted interference. A benefit of this configuration is that the shield only needs to be connected to ground at one end of the cable in order for it to work. Having this ground disconnected or “lifted” at one end can eliminate the ground loop problem discussed in the previous section on unbalanced lines. (Exception: the shield must be connected at both ends when transmitting phantom power because it acts as the ground return for the phantom current. Phantom power will not work if the ground is lifted at either end.)
The two center conductors of a balanced line act as the sole conduit for the signal.
Now, if any unwanted electrical interference enters these signal conductors and because they have the same impedance to ground, it will interact with both center conductors equally. The effect in the receiving circuitry is that these equal voltages can be made to effectively cancel each other out - the noise disappears.
This ability of balanced lines to reject noise and interference makes them popular when it is necessary to send signals over long distances.
Whirlwind Accusonic+2 balanced cable features full braided shield and two 22 ga. finely stranded center conductors for increased flexibility.
- Opening Pandora’s Box?The “L” word - latency and digital audio systems By Al Keltz
- Microphone Splittersby Al Keltz
- Getting It Wired by Carl Cornell
- Wiring MASS Connectors FAQ It’s really a simple job to get a MASS connector system wired correctly if a few basic conventions are adhered to.
- Basics of Troubleshooting Sound Systems by Al Keltz
- High and Low Impedance Signals by Al Keltz
- A Direct Box can be in-DI-spensibleWhat direct boxes (DIs) do and what are the different types. By Al Keltz
- Unbalanced vs. Balanced LinesHow they work and the difference between them. By Al Keltz
- The Whirlwind E SnakeDetails of an E Snake install at Bucknell University From an article by Mike Sokol in “Live Sound Intl.”
- “Press Conference Audio Distribution”Procedures and required gear for feeding the press. By Al Keltz